Showing results: 406 - 420 of 422 items found.
-
Teledyne Marine DGO
This Electrical Feedthrough System design provides a high-reliability circuit for transmitting electrical signals from downhole gauges through the wellhead and Subsea Tree to the Subsea Control Module (SCM) for topside monitoring. The system incorporates Teledyne DGO's high integrity glass-seal technology in three critical pressure barriers for maximum long-term reliability. The feedthrough system creates a permanent connection to the Subsea Control Module when the tree is installed onto the wellhead. In addition, a permanent rig-based DHG cable termination is completed to connect the control line to the feedthrough system. The DHG connector is available with a variety of sealing packages, including fully testable, dual metal-to-metal sealing of all downhole tubing hanger interfaces.
-
Precise Time and Frequency, Inc.
With intense competition and subscribers demanding ever more from service providers, quality and availability of service have never been more critical to maintaining and expanding your subscriber base.To complement our range of our high quality frequency and timing references, Precise Time and Frequency, Inc. has now introduced a new RF, Digital, and Time Code, Auto Switch / Distribution unit to insure you deliver the performance and reliability your customers demand.The ptf 1207A delivers up to eight channels of fully redundant, frequency and timing references to critical applications such as Satellite Communications, Broadcasting, WiMax and others, with NO SINGLE POINT OF FAILURE.The unit accepts two inputs on each channel from separate sources (primary and backup), monitors the inputs for signal integrity, and outputs the primary signal with no degradation of the input.If the primary input on any channel fails, the unit will automatically switch to the backup input and indicate a primary signal fault.The unit will accept up to eight channels simultaneously and independently switch on each channel.The unit also includes full remote monitoring and control via RS232 and Ethernet interfaces.
-
EPS Series -
ADLINK Technology Inc.
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
multiLane
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Dynamic Test Solutions
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
Keysight Technologies
When you need to measure advanced S-parameters with a fast, low-cost and easy-to-use test solution, the Digital Interconnect Test System gives you a significant edge. It provides a full 32-port vector network analyzer (VNA) configured within a single PXI chassis – ideal for high-speed cable testing. And lets you test any linear passive interconnect faster and easier, including backplanes, connectors and PCBs. Sharpen your edge with Keysight’s Digital Interconnect Test System that enables signal integrity characterization of multiport interconnect products.
-
Ironwood Electronics
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Ironwood Electronics
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
SG1000B/PR1000A -
Praxsym
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Model 5585 -
Pentek, Inc.
- Jade 5585 and 5586 FAQ- Complete radar and software radio interface- Wideband data acquisition- Multi-channel, multi-board synchronization for high channel count systems- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX processing powerhouse- Exceptional dynamic range and analog signal integrity- Features Xilinx Virtex UltraScale+ HBM FPGAs- Eight 250MHz 16-bit A/Ds- 10 GigE Interface- 40 GigE Interface- Dual 100 GigE UDP interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Navigation Design Suite for software and custom IP development
-
Fairview Microwave Inc.
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
TP800110 -
Total Phase Inc.
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
LEON Bench -
Konrad Technologies GmbH
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, Inc. has now introduced a new version of the ptf 1226A Auto Switch that includes an additional switch channel (now 3 channels total) of RF, and/or Digital, and/or Time Code, Auto Switching, and a full Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1226 delivers up to thirty six channels of RF, Digital or Time Code frequency and/or timing references to critical applications such as Satellite Communications, Broadcasting, WiMax and others.Analog channels include a unique output level monitoring feature to provide remote indication of rms voltage output level.The unit can accept up to three pairs of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity. In addition RF channels include analog level monitoring. If the primary input on any auto switch channel fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Model 54141A -
Pentek, Inc.
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range and analog signal integrity- Xilinx® Kintex® UltraScale™ FPGAs- Compatible with several VITA standards including: VITA 66.5 and VITA 67.3C- Supports VITA 49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/Ds- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- uSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Navigator® BSP for software development- Navigator® FDK for custom IP development- SPARK® fully-integrated development system
